Miracle skirt

Send

Despite the simple cut of this model, lace tulle on top of the rustling taffeta of the Shanjan creates a charming effect!

YOU WILL NEED
• tanja of Shanjans 150 cm wide, sizes 34−44 - 0.80 m; • for the upper skirt: tulle lace fabric with a metallic effect and scalloped edge 2.35 m wide 95 cm; • non-woven G 785 0.10 m wide 90 cm; • 1 secret fastener-zipper 22 cm long and a special foot of the sewing machine for its sewing; • 1 button for sewing; • threads for sewing
In addition: • silk paper for transferring patterns from a sheet of patterns; • pencil, paper scissors; • tape measure; • tailor pins; • tailor's chalk; • burda carbon paper, cutter for pattern translation; • scissors for cutting and small scissors for needlework; • sewing machine needle and manual sewing needle.
Length from waist 65 cm.
The upper edge of the belt lies at the waist.
Sizes 34-44

Extra-pattern of pink color on a sheet of patterns A
Details 1 and 2
SKIRT PATTERN
... pink, so it is easy to find on the sheets of patterns. Put silk paper on a sheet of patterns and pin it. Translate the details of the pattern of your size along the corresponding contour lines and do not forget about the marking and inscriptions. For the belt and upper skirt, special details of the paper pattern are not provided. Draw these details directly on the fabric and cut. Dimensions are shown on the right.
Extra tip: the size of the skirt is determined by the circumference of the hips (size 34 = 86 cm; size 36 = 90 cm, 38 = 94 cm, size 40 = 98 cm, size 42 = 102 cm, size 44 = 106 cm )

150 cm wide Shanjang taffeta
Sizes 34−44
LAYOUT PLAN
... shows how to arrange the details of the paper pattern on the fabric.
Pin the details of the paper pattern.
1 Front panel of the skirt with a fold 1x
2 Rear panel of the skirt 2x
a) belt length: size 34 - 69 cm, size 36 - 73 cm, size 38 - 77 cm, size 40 - 81 cm, size 42 - 85 cm, size 44 - 89 cm and a width of 5 cm, including allowances.

STEP 1
OPEN TANKS SHANZHAN
Fold the fabric along in half with the front side inward. Apply the details of the paper pattern to the fabric, while aligning the middle section of part 1 with the fold of the fabric. Pin it up. Mark around the details of the pattern with tailor's chalk allowances: for hem hem - 4 cm, for upper sections of skirt panels - 1 cm, for other sections - 1.5 cm. Cut out details. Unfold the remaining flap. On the fabric, draw a belt (a), cut it out. Also cut the belt out of the pad. Press the gasket to the wrong side of the belt.

STEP 2
CUTTING TULE LACE CANVAS
For the upper skirt from the scalloped edge of the tulle lace fabric, measure 65 cm, draw a line. Cut the upper skirt along this line. On the remaining patch of tulle lace fabric, draw a belt (a), cut it out. Put the tulle belt with the wrong side on the front side of the belt from the tanja of the Shanjans, outline along the contour.

STEP 3
SEAM LINES AND STAMPING
If you cut the parts exactly along the drawn allowance lines, then the lines of the seams and the lower edges on the cut parts can not be transferred. At transverse cut marks for zippers, perform 5 mm notches on the allowances of the details of the cut. Transfer dart lines with a cutter to translate patterns and carbon paper (see detailed instructions on paper packaging).

STEP 4
DIRECTIONS
Fold each panel of the skirt, respectively, along the line of the middle of each tuck with the front side inward. Chip off the tuck lines, grind off, starting the line from the top cut of the skirt panel. At the beginning of the stitch, bind, do not bind at the top of the tuck, but bind the stitches. Iron tuck depths to midline of front / back.

STEP 5
LATERAL SEAMS
Place the rear skirt panels on the front skirt panel with the front side to the front side, chip the side sections, grind with allowances 1.5 cm wide. Seam allowances and iron over seams.

STEP 6
PICK UP TOP SKIRT
To do this, along the upper section of the skirt at a distance of 7 mm, lay the machine stitch with large stitches. Lay another stitch 5 mm from the first stitch. Hold the lower threads of the sewing stitches tightly, pull the fabric of the upper skirt on the stitches to the width of the taffeta skirt along the upper cut. Tie the threads of the sewing lines. Distribute the assembly evenly.

STEP 7
STOP UP TOP SKIRT
Put the upper skirt on the taffeta skirt with the wrong side to the front side. Sweep the upper and rear middle sections to the transverse section mark for the zipper (see step 3).

STEP 8
Zipper
RIGHT HALF
Open the hidden hidden zipper with the top side down along the edge of the cut for the zipper of the right rear panel of the skirt at a distance of 5 mm from the cut. The upper cloves of the hidden zipper are at a distance of 1 cm from the upper cut of the skirt. Sew the hidden zipper to the cut mark (notch) with the special foot of the sewing machine. The sewing machine needle is located to the left of the cloves.

STEP 9
Zipper, LEFT HALF
Close the zipper. Place the second tape of the hidden zipper along the edge of the section for the zipper of the left rear panel of the skirt, pin it at the top. Open the zipper again and sew the second tape of the hidden zipper to the cut mark. The needle of the sewing machine is located to the right of the cloves.

STEP 10
REAR MIDDLE SEAM
ON THE SKIRT FROM TAJA SHANZHAN
At the lower end of the zipper on the allowances of the tulle skirt, make notches close to the last stitches of the seams for attaching the hidden zipper. Turn the tulle skirt up. Fold the back panels of the taffeta skirt with the front sides, chop the middle sections from the bottom to the cut mark (zipper), while pulling the free end of the hidden zipper out. Stitch slices (allowance width 1.5 cm).

STEP 11
REAR MID
ON THE SKIRT FROM TULA
On the upper skirt, fold the rear middle sections with the front sides and grind from the bottom to the notch with allowances 1.5 cm wide. Cut the seam allowances to 7 mm wide and iron in one direction. On the taffeta skirt, overcast and iron the seam allowances.

STEP 12
GRIND BELT
Fold the belt along in half with the wrong side (gasket) inward. Iron the fold. Fold the belt again and pin it to the upper section of the skirt with the front side to the front side, while at the right edge of the zipper, the end of the belt protrudes 1 cm, at the left edge of the zipper - 3 cm. Stitch (allowance width 1 cm). Iron seam seam allowances on the belt. Iron another longitudinal section of the belt on the wrong side, 1 cm wide.

STEP 13
CLEAN THE BELT ENDS
Fold the belt along the curved bend with the front side inwards. At the ends of the belt grind short sections with allowances of 1 cm. At the corners of the seam allowances, cut obliquely. Turn out a belt. Pin the inner half of the belt over the stitching seam. On the front side, sew the belt along the seam of the seam close to the seam, securing the inner half of the belt.

STEP 14
SEW THE BUTTON
Sew the upper part of the button to the right end of the belt from the wrong side with uniform stitches, leading the needle to the front / wrong side of the belt. Sew the bottom of the button to the left end of the belt (buckle allowance).

STEP 15
FIT NIZE
On a skirt from a tanja of Shanjans, sew an allowance for hem in the hem, iron on the wrong side to a width of 4 cm and sew it manually with unstretched stitches.
PHOTO: U2 / ULI GLAZEMAN. TEXT: HYDEMARIA TENGLER. ILLUSTRATIONS: ELKE TRIER-SHAFER.

Send